Process Paves Way For More Efficient Lasers, LEDs

News Source: 


North Carolina State University team develops MOCVD process that produces the highest concentration of holes in p-type III-Nitride material

Researchers from North Carolina State University have developed a new process that makes use of existing industry standard techniques for making III-nitride semiconductor materials, but results in layered materials that will make LEDs and lasers more efficient.

A challenge for people who make LEDs and lasers has been that there was a limit on the number of holes that you can make in p-type III-nitride semiconductor materials that are created using MOCVD. But that limit just went up.

“We have developed a process that produces the highest concentration of holes in p-type material in any III-Nitride semiconductor made using MOCVD,” says Salah Bedair, co-author of a paper on the work and a distinguished professor of electrical and computer engineering at NC State. “And this is high quality material - very few defects - making it suitable for use in a variety of devices.”

In practical terms, this means more of the energy input in LEDs is converted into light. For lasers, it means that less of the energy input will be wasted as heat by reducing the metal contact resistance.

LEDs contain three main layers: an n-type layer where electrons originate; the “active region,” which consists of multiple quantum wells of InGaN and GaN and a p-type layer, where the holes originate.

The researchers use a growth technique called “semibulk growth” to produce InGaN templates. The template is made of dozens of layers of InGaN and GaN. The researchers use these templates for the n-type region to reduce complications that arise with the growth of the quantum wells. The insertion of the GaN layer in between the InGaN layers in semibulk reduces defects due to the lattice mismatch between the semibulk template and the GaN substrate, as well as filling the pits that form on the surface.

In their new work, the researchers demonstrated that the semibulk growth approach can be used for the p-type layer in LEDs to increase the number of holes. This new approach is cost effective from a manufacturing standpoint, since III-nitride based LED devices can be done in one growth via MOCVD, without a lengthy processing time in between.

Using this technique, the researchers were able to achieve a hole density of 5 × 1019 cm-3 in the p-type material. Previously, the highest hole concentration achieved in p-type III-nitride materials using MOCVD was about an order of magnitude lower.

The researchers also applied these InGaN templates as substrates for LED structures to address the long-lasting problem called the “green gap,” where the LED output deteriorates when emitting in the green and yellow part of the spectrum.

One of the main reasons for the green gap is the large lattice mismatch between the light emitting part of the material, the quantum well, when gallium nitride substrates are used. The researchers have demonstrated that replacing the GaN substrates with InGaN templates results in improved LED performances.

The researchers compared the LED emission spectrum for the same quantum well emitting in blue when grown on GaN substrate and emitting either in green or yellow when grown on different indium gallium nitride templates. A 100 nm shift in the emission wavelength was achieved due to the application of the InGaN templates.

The graphs above show electroluminescence measurements of (a) Blue LED on GaN, (b) Green LED on InGaN template, (c) Near yellow LED on InGaN template. The insets of Fig. 1(b) and Fig. 1(c) show the image of the emission at 1.5 mA injection current.

'P-type InxGa1-xN semibulk templates (0.02 < x < 0.16) with room temperature hole concentration of mid-1019 cm-3 and device quality surface morphology” is published in the journal Applied Physics Letters.

'Shifting LED emission from blue to the green gap spectral range using In0.12Ga0.88N relaxed templates' is published in Superlattices and Microstructures

Disclaimers of Warranties
1. The website does not warrant the following:
1.1 The services from the website meets your requirement;
1.2 The accuracy, completeness, or timeliness of the service;
1.3 The accuracy, reliability of conclusions drawn from using the service;
1.4 The accuracy, completeness, or timeliness, or security of any information that you download from the website
2. The services provided by the website is intended for your reference only. The website shall be not be responsible for investment decisions, damages, or other losses resulting from use of the website or the information contained therein<
Proprietary Rights
You may not reproduce, modify, create derivative works from, display, perform, publish, distribute, disseminate, broadcast or circulate to any third party, any materials contained on the services without the express prior written consent of the website or its legal owner.

New flux bin options offer even better optical performance and efficacy Cree LED has introduced XLamp XP-G3 S Line and XP-G4 White LEDs that are now brighter, with new minimum flux bin options for drop-in increases of output and efficacy. XP-G... READ MORE

For decades, Cree LED has been at the forefront of video LED technology, setting the industry benchmark for large-format displays, digital signage and video screens used in sporting events, concerts and commercial installations. Our expansive ... READ MORE